- Honeywell vista 20p installation manual pdf rev c how to#
- Honeywell vista 20p installation manual pdf rev c upgrade#
- Honeywell vista 20p installation manual pdf rev c code#
Honeywell vista 20p installation manual pdf rev c code#
(Installer Code + 8 + 01 + New 4 Digit Master Code) If you're following my instructions and it's not working, then either you're pausing too long between digits (if you pause for more than 2 seconds between the entry of numbers, it's as if you started over to the panel, it has very poor short term memory) of you're performing these steps on a partition 2 keypad, which wouldn't work. If the code you have gets you into programming, and you can review the Installer Code by pressing #20, then I would recommend (and this is based on the panel being a Vista-20SE, and not a Vista-20P, which is the document page we're actually having this discussion on) you press *29 then 0, this will disable the AlarmNet device so you stop getting the bF message (at least until you can sort out what you want to do) then press *99 to exit programming then follow my original instructions. This code wouldn't allow you to change other users. I believe what you are using may be the Duress code, which will arm/disarm, but will also report a Duress signal to monitoring, if enabled. I do own an alarm now, and if I signed up, then cancelled, I might no longer own an alarm.) The tech called his supervisor, who called P-1, and after an hour of waiting, was told that while no changes could be made to the contract, it was almost unheard of for the company to remove installed equipment. (He indicated that he had learned something new that day) Secondly, the contract repeatedly mentioned that certain installed property would remain the property of the company and was subject to removal upon contract cancellation. The tech had informed me, and continued to inform me, that he had always believed that after the initial term, 30-days notice at any time was all that was required to cancel. Two problems squelched it.įirst, the two-year contract provided that if I did not cancel during a fairly limited period of time, then the contract extended for another 12 months. He intended to put in a new board and a new 5g(?) communicator. (Note that a P-1 sub-contractor/installer came close to signing me up for monitoring, but he was experienced enough to prepare for the job very slowly while I read the contract.
Honeywell vista 20p installation manual pdf rev c upgrade#
Maybe I do not wait long enough between failed attempts? Further, I have rather poor hearing and am not always able to hear the beeps from the 6128 KP very well-and/or perhaps the KP is not working so well.Īm I correct that if I have successfully changed the MC, then with it I should be able to change/remove other user codes? If so, can you simplify for me what would be the best/easiest way to remove any other codes? I have no idea what might be in there, except that there is at least the one "limited use" UC which I stumbled upon, and which you suggested could be a duress or babysitting code?Īlso, are there any newer/more advanced keypads that I could easily upgrade to? But my ability to make changes is sketchy. I have (I think/am reasonably confident that I have. I hope that helps clarify things for you and please let us know if you have any follow up questions.
Honeywell vista 20p installation manual pdf rev c how to#
Finally, for people that are looking to buy product and not be monitored at all, we'll certainly provide those people with help during the install but as we don't have the means of programming remotely (like we do with a monitored client), some of the help we'll provide will be to show you where in the manufacturer's guide it says how to do things so that you'd be able to install it yourself. Those people always have the option to switch to us, as long as they aren't under contract, of course. If he's not monitored by us, he should ask his company to remove it for him as we don't provide technical support to people monitored elsewhere, for liability purposes. If Vincent was monitored by us, it would be very easy to remove a zone remotely for him. Jorge's reply was trying to cover all bases. Also, we tend to get posts on our pages from existing customers using unknown emails. Oftentimes, to properly troubleshoot, we need access to the system programming and monitoring settings.
0 kommentar(er)
